Remove the Case cover by unscrewing the 4 to 6 screws and taking the quilt off. Lay the Case on its facet with the metallic lower backplate dealing up to you. Some instances come with a preinstalled PSU; others do not. To set up a PSU, slide the PSU into the region with the wires going forward into the Case and the fan blowing out the returned. Secure it in the vicinity with a few screws so that it does now not pass. Set the voltage to 220 inside the UK and 120 in the USA. The lower backplate may additionally want to change to be your Motherboard. To do that, wreck off the old plate and take the new scale (full of the Motherboard), and installation is in the vicinity of the vintage one.

The Motherboard must be sat on a relaxed floor in/on the antistatic bag it came in. To install the CPU, make sure the lever at the Motherboard is up (talk to the guide furnished with your Motherboard to peer how that is carried out), and take the processor out of the box it got here in by using the most effective touching the rims of the chip. Place this into the socket with the aid of matching pin 1 to the right area on the Motherboard.

ComputerUsually, a gold arrow lines up with any other mark on the socket. Once in the vicinity, Push the lever arm down to lock the processor in place. To install the Heat Sink/fan onto the processor, clean the processor with a loose lint material to get rid of dirt and finger oil. Take the cooling compound and squirt a small amount onto the processor without delay, taking care not to apply too much as it can cross over the edges.

Spread this lightly over the surface of the processor.

Take the Heat Sink and area it without delay on the pinnacle of the processor, pushing down slightly to make the sure desirable connection between the processor/compound and the Heat Sink. Using the clips on either side of the Heat Sink, comfy this in a location on top of the processor. Check that no cooling compound has leaked from the edges; otherwise, you have to begin once more and clean both the Processor and Heat Sink. Once the Heat Sink is in the vicinity, plug the power wire attached to it into the Motherboard. See the manual supplied along with your Motherboard to decide which one. This is step 1 entire.

Step 2…Install memory modules (RAM) and Motherboard into the Case.

To deploy the reminiscence modules, attach the antistatic wrist strap to an unpainted steel surface to earth yourself and discharge any built-up static. On the Motherboard, you should see the slot for the memory module. Make sure the clips at both quits are open, i.e., Tilted backward. Please pick up the reminiscence module using the edges and region it into the slot by lining up the notches and ensuring both ends are the clips. Push down firmly, and the pins have to pop shut. This is the reminiscence Installed.

The Motherboard ought to now have the processor, Heat Sink, and memory mounted. The Motherboard can be placed directly into the Case. To deploy the Motherboard into the Case, examine the holes on the Motherboard and the holes on the motherboard plate in the Case. Take the motherboard standoff screws and screw them into the motherboard plate consistent with the holes on the Motherboard.

Once that is executed, take the Motherboard and place it into the Case with the inputs and outputs facing closer to the again of the Case. These should be healthy on the back plate of the Case. Take some screws and screw the Motherboard into the standoffs. Do no longer screw too tightly. In any other case, the circuits at the Motherboard may break but sufficient, so there may be no movement. Step 2 is whole.

Step 3…Connect the Motherboard to the Case Wires and PSU

Now the Motherboard is in place, take the 20 or 24-pin connector from the strength deliver and connect it to the Motherboard. The board may additionally require a 44-pinconnector to electricity the CPU. Plug this in, too. The Case should also have a hard and fast number of wires if you want to plug into the Motherboard. Talk to the guide provided together with your Motherboard to install these effectively. Usually, the connector labeled PWR_SW is the strength switch, and RST is the RESET button. The Power LED and Hard Drive LED should also be attached. Once all the connectors are connected, circulate to Step Four.

Step 4…Install the Floppy Drive, Hard Drive, and CD ROM Drive

To set up the floppy Power, select which force bay you need the floppy drive in and do away with the face plate at the Case. Slide the drive in from the front and make sure it lines up with the face plate as well as the screw holes on the mounting rack. Screw the pressure into the vicinity. Connect the electricity delivered to the floppy force, which is the smallest connector coming out of the PSU. Take the ribbon cable and fix it to the lower back of the floppy Power; this cable has a twist in it. Attach this to the Motherboard, lining up the red side. If you do not line this up, the force, in reality, won’t paint. When attached to the port on the Motherboard, the floppy power is established.

To install the Hard Drive, determine which bay you’re going to put it in. Slide it in from the returned and match up the screw holes to the mounting plate. When this is executed, comfy it in the vicinity, and attach the 4-pin Molex connector from the PSU to the Power again; it will fit one manner best. If the pressure is IDE, it will have a big connector at the lower back; if this is the case, take the ribbon cable and fix this to IDE 1 on the Motherboard. If the drive is SATA, the connector can be smaller and the line a lot thinner. If this is the case, take the bar and fasten it to the returned drive, then to SATA_1 at the Motherboard. This is the hard pressure installed.

To set up the CD ROM power, this is just like the floppy pressure. Choose which bay you want it in, and take the faceplate off. Slide the force in from the front and screw it into the vicinity. Attach the 4-pin Molex connector as you did with the difficult Power, and then take the ribbon cable and fix this to IDE_2 on the Motherboard. This is Step Four whole.

Step 5… Install the Video Card

A video card is needed so that you can see the output of your PC. There are two kinds of used: older AGP cards and newer PCI Express Cards. To install a Video Card, you must see a brown slot known as an AGP slot. If your card is AGP, then it goes here. Open the space at the back of the AGP slot. There may be a clip-like with the reminiscence modules to aid the cardboard, as they’re now pretty large. Break off the metallic protecting the hole in the back of the Case. Take the video card with the aid of retaining the edges handiest and slot it into

Press down firmly; you need to experience it and click into the area. Do not over-pressure it, as this will damage the circuits and your Motherboard. Once in a location, secure the cardboard with the aid of screwing it to the back of the Case. You must see this on the metal plate at the return. Some Video Cards require extra electricity now, so connect the 44-pinMolex connector to the video card. This is the Video Card Installed.